Should I Insulate My Attic Floor Or Ceiling?

How do you insulate an unfinished attic ceiling?

To insulate an attic, start by preparing the space.

This includes any baffles that will hold insulation away from roof sheathing and electrical fixtures.

Install a vapor barrier if needed.

You can choose either fiberglass insulation or loose fill insulation for the project..

Can attic insulation touch the roof?

The airflow from the soffits to the ridge vent keeps the roof cool and prevents ice dams, and the material will block that flow. For the same reason, insulation shouldn’t touch the roof’s underside. Staple plastic or foam baffles to the roof sheathing, near the eaves, to keep the material away.

How much does it cost to insulate a 1500 sq ft attic?

Attic Insulation CostsItemUnit CostCostInsulation: install Kraft faced R-19, 23″ wide x 6.25″ thick x 1,500 sq.ft.; prepare and clean up; including waste and miscellaneous material.$0.64$1,053+ Labor Cost$32$448Total Cost$1.00$1,501

Is insulating the attic worth it?

Installing attic insulation this winter is a worthwhile long-term investment because it can significantly decrease your heating bills. As an added benefit, when the hot D.C. temperatures come back, the attic insulation will also minimize your air conditioning bills.

Should you insulate roof rafters?

Insulating between rafters will do no good, because the attic should be ventilated, and the rafter insulation would be between two unheated spaces. You can add insulation to the floor; the more the merrier. … Also, make sure the attic is well ventilated. Cold roofs prevent ice dams.

What happens if attic is not vented?

But in homes without appropriate insulation and ventilation in the attic, heat migrates. … Meanwhile, because hot air is full of moisture, all that water hanging out in your attic is causing condensation to build up. Excess heat and condensation can cause major damage to your roof and roofing materials.

What is the best insulation for an attic ceiling?

Also known as loose-fill, blown-in insulation comes in tiny chunks packaged in large bags, and entails using a blowing machine to fill in necessary spaces. Fiberglass, cotton, and mineral wool can all work as loose-fill material, but the far and away top choice for blown-in insulation is fiberglass.

Does a finished attic need to be vented?

When done correctly, attic venting can reduce the potential for condensation in winter and summer. … Even when outside air is hot and humid, if the attic space is air-sealed from the interior, it is much hotter than outside air. The hotter the air, the more moisture (i.e. absolute humidity) the air space can hold.

How long does Attic Insulation last?

As a rule of thumb, we recommend checking your roof insulation every 15 years as standard insulation may start to degrade after this time. If your insulation is old, then there’s a chance gaps may be present and air drafts as a result.

What happens if I don’t insulate my attic?

The solution is simple—insulation keeps your home warm in the winter and cool in the summer. Every part of your home works together, from the basement to the main floor, to your attic. If there’s any air to seep from cracks or anything, it’ll seep, increasing the need for energy to heat or cool your home.

Can you put too much insulation in attic?

But there may be a theoretical point of “too much.” If a home is over-insulated and is too tightly sealed, moisture can get trapped inside. Without proper ventilation, a home can build up too much moisture, especially in the attic (warm air rises), which can cause mold problems and, overall, lower indoor air quality.

How many inches of insulation should be in my attic?

The higher the R-Value, the better the thermal performance of the insulation. The recommended level for most attics is to insulate to R-38 or about 10 to 14 inches, depending on insulation type.

How do you ventilate a finished attic?

To effectively ventilate your roof, create a 1-inch airspace from the soffit to the ridge by installing a continuous air chute in each rafter bay. Note: Air chutes, when combined with soffit vents and a ridge vent, will help prevent problems with condensation and ice dams.

Can I put plywood over insulation in attic?

An attic can be floored with 1/2″ CDX plywood, if it is being used only for storage. However, the same can’t be said if you are planning on using the space as a living space. In that case, you will need to use 3/4″ thick plywood. … The building code allows for the use of OSB in place of plywood for subflooring.